Tripp Lite SmartPro Tower 1050 UPS System SMART1050

Tripp Lite Smart 1050 SmartPro Tower UPS System SMART1050 intelligent, line interactive UPS system protects servers, networking accessories and telecommunications equipment from blackouts, voltage fluctuations and transient surges. Large internal batteries offer 23 minutes half load runtime and 8 minutes at full load during power failures. 1050VA / 680 watt power handling capability supports a variety of networking, telecom and various other application types, including the support of multiple network workstations. Includes a total of 6 UPS supported outlets. Supports remote monitoring of UPS and site power conditions via built-in USB monitoring port. Includes PowerAlert UPS monitoring and unattended shutdown software with complete cabling. Built-in audible alarm and 5 front panel LEDs indicate status of line power, battery power, battery low/replace, voltage regulation and load level. Wall mountable with UPSWM wallmount bracket. Network-grade AC surge suppression protects equipment from damage and performance problems resulting from transient surges. Attractive, small-footprint tower housing uses less than 53 square inches of floor or desktop space. Two year manufacturer's warranty with $250,000 connected equipment insurance.

KEY BUYING POINTS

1050VA / 705 watt power handling capability supports a variety of networking, telecom and various other application types

Built-in voltage regulation and battery support prevents equipment damage, data loss and downtime

Large internal batteries offer 23 minutes half load runtime and 8 minutes at full load during power failures

Automatic Voltage Regulation (AVR) circuits with two boost and one voltage reduction level maintains usable 120V nominal output over an input voltage range of 75-147V

Includes a total of 6 NEMA5-15R outlets

Includes 1 USB communications port for remote monitoring of UPS status and site power conditions

Communications port enables safe unattended shutdown without data loss during extended power failures

Communications port supports messaging of UPS and line power status, including on-battery, low-battery, power-restored, AC line voltage, DC battery voltage and battery capacity

Communications port supports timed inverter shutoff after unattended shutdown, activate self-test and 10 second reboot of connected equipment

PowerAlert UPS monitoring and unattended shutdown software with complete cabling included

Supports Tripp Lite's WatchDog software application to restore unresponsive programs by automatically restarting them and rebooting completely locked computers by automatically switching UPS power off and back on again

Notification of system status via 5 LEDs and multi-function audible alarms

Wall mountable with UPSWM wallmount bracket

Attractive small footprint beige tower housing uses less than 53 square inches

Hot-swappable / user replaceable batteries allow on-site battery replacement

Cold start capability enables UPS turn-on in battery mode during blackout conditions

UL (USA), cUL (Canada), NOM (Mexico), FCC Class B Listed

$250,000 Ultimate Manufacturer's Lifetime Insurance

2 year manufacturers product warranty

TYPICAL APPLICATIONS

Ideal for the protection of fileservers, network accessories and telecommunications equipment. Common applications include any mix of servers, workstations, hubs, routers, concentrators, IP telephony and traditional PBX switching systems. Ideal for sensitive electronic applications in areas where brownouts and overvoltages are common.

OPTIONS & ACCESSORIES

USB Hubs-accessories: U202-004-R, U205-004-R, DUSB, U022-010 / Dataline protectors: DNET1, DTEL2, DCATV / Wallmount Bracket: UPSWM / Circuit Tester: CT120 / Power Distribution: PDU1215

PACKAGE INCLUDES

SMART1050 UPS System, USB monitoring cable, PowerAlert unattended shutdown and UPS/Power monitoring software, Instruction manual with warranty information

COMPLETE SPECIFICATIONS SYSTEM OVERVIEW System overview: Line interactive tower UPS protects internetworking and telecommunications equipment from blackouts, brownouts, overvoltages, surges and line noise. Maintains AC output during blackouts and continuously corrects brownouts and overvoltages from 75 to 147 volts back to normal 120V levels. Supports enhanced monitoring of UPS and line power conditions via USB serial port, included PowerAlert UPS monitoring software and cabling. Voltage compatibility: 120V AC Frequency compatibility: 60Hz OUTPUT Output volt amp capacity (VA): 1050 Output watt capacity (watts): 705 Output nominal voltage: 120V AC Output voltage regulation: LINE MODE: Sine wave line voltage 120V (-18% / +8%), BATTERY MODE: PWM sine wave output 120V +/-5% Output frequency regulation: LINE MODE: Passes line frequency of 60Hz +/-10% BATTERY MODE: Inverter output regulated to 60Hz +/-0.5Hz Outlet quantity / type: 6 NEMA 5-15R Overload protection: 12A input breaker INPUT Maximum input amps: 6.7A /760 watts Input connection type: NEMA 5-15P Input cord length: 6 ft., 16 gauge Recommended electrical service: 15A 120V BATTERY Full load runtime: 8 minutes (1050VA) Half load runtime: 23 minutes (525VA) DC system voltage: 18 VDC Typical battery lifespan: 3-6 years, depending on usage Battery recharge rate: 2-4 hours to 90% VOLTAGE REGULATION Voltage regulation description: Automatic Voltage Regulation (AVR) circuits maintain clean, regulated computer-grade 120V nominal output, without using battery power, during brownouts to 75V and overvoltages to 147V Overvoltage correction: Input voltages between 128 and 147VAC are reduced by 12% Direct pass through: Input voltages between 108 and 127VAC are passed on to connected equipment unchanged Brownout correction: Input voltages between 108 and 127VAC are passed on to connected equipment unchanged Severe brownout correction: Input voltages between 75 and 92VAC are boosted by 30% LEDS ALARMS & SWITCHES Front panel LEDs: Includes 5 front panel LEDs to indicate BATTERY CHARGE LEVEL, AC LINE POWER STATUS, VOLTAGE REGULATION STATUS, UPS LOAD LEVEL and BATTERY LOW / REPLACE information Alarms: Audible alarm with 15 second delay sounds to indicate loss of utility power. Alarm can be silenced by pressing front panel alarm cancel button. Once silenced, alarm will re-sound when approximately 2 minutes runtime remain. Switches: Includes 2 front panel switches — one main on/off power switch and one dual function "alarm cancel" / "self test" button SURGE / NOISE SUPPRESSION AC surge suppression: 480 joules AC suppression response time: Instantaneous EMI / RFI AC noise suppression: Yes PHYSICAL Shipping weight (lbs): 31 Shipping weight (kg): 14.1 Unit weight (lbs): 29 Unit weight (kg): 13.2 Unit Dimensions (HWD/in): 11.75 x 7.25 x 7.25 Unit Dimensions (HWD/cm): 29.8 x 18.4 x 18.4 Shipping Dimensions (HWD/in): 15 x 10.75 x 11.25 Shipping Dimensions (HWD/cm): 38.1 x 27.3 x 28.6 Material of construction: Polycarbonate Form factors supported: Tower Cooling method: Convection Battery Access: Battery access door allows user replacement of UPS batteries ENVIRONMENTAL Operating Temperature: +32 to +104 degrees Fahrenheit 0 to +40 degrees Celsius Storage Temperature: +5 to +122 degrees Fahrenheit -15 to +50 degrees Celsius Relative Humidity: 0 to 95%, non-condensing Line mode BTU/hr. (Max.): 61.5 Battery mode BTU/hr. (Max.): 208.4 COMMUNICATIONS Network monitoring port: Built-in USB port supports on battery, low battery, power restored, AC line voltage, DC battery voltage, load percentage, battery charge current, battery capacity, internal UPS temperature and line frequency status messaging. Interface supports timed inverter shutoff after unattended shutdown, activate self-test and 10 second reboot of connected equipment. Supports reboot of all connected devices at once via software interface. Compatible with Tripp Lite's PowerAlert software. Software and cabling included: Includes PowerAlert UPS monitoring and auto-shutdown software and cabling WatchDog compatibility: Compatible with Tripp Lite's Watchdog system service to restore operation to locked equipment through soft reboot of application / OS or hard power off/on reboot of connected equipment - ideal for unattended kiosk applications LINE / BATTERY TRANSFER Transfer time from line power to battery mode: 2-4 milliseconds Low voltage transfer to battery power: Switches to battery power as line voltage decreases to 75 volts or less. Resets back to line power mode as line voltage increases to 79V or higher. High voltage transfer to battery power: Switches to battery power as line voltage increases to 147 volts or higher. Resets back to line power mode as line voltage decreases to 143V or less. CERTIFICATIONS Certifications: UL1778 (USA), cUL (Canada), FCC Class B (emissions), NOM (Mexico) WARRANTY Optional coverage: 3-5 year warranties, plus next day and on-site warranty coverage available for select opportunities. Contact Tripp Lite for additional information. Product warranty: 2 year product warranty Connected equipment insurance (USA and Canada Only): $250,000 connected equipment insurance (USA / Canada only) SPECIAL FEATURES Cold Start: Yes, inverter can be "cold started" to enable temporary AC output during a power failure Appearance: Attractive gray tower UPS

		Tripp Lite SMART1050 Brochure				Tripp Lite SmartPro SLT Owners Manual